- 您现在的位置：买卖IC网 > Sheet目录961 > AS1112 EB (ams)BOARD EVAL AS1112
AS1112
Datasheet - D e t a i l e d D e s c r i p t i o n
Figure 10. Error Detection Timing (GS=FFFF HEX , DC=3F HEX )
LD
>1μs
OEN
GSCLK
SID
Error
Detection
Start
LOD n , LSD n
LOD n+1 , LSD n+1
Error
Detection
End
Note: The rising edge of LD latches new data into the internal registers depending on the logic level of the pin MODE. If the pin MODE is tied
GND, the greyscale registers are updated. If the pin MODE is tied to V CC , the dot correction registers are updated.
Delay Between Outputs (only for AS1112 and AS1112B)
The AS1112 uses graduated delay circuits between OUT n outputs. These circuits are contained in the constant-current driver block of the
AS1112 (see Figure 1 on page 1) . The average-delay time is 30ns (typ).
The maximum delay is 450ns (typ) from OUT0 to OUT15. The delay scheme works by switching on and switching off each output channel. Thus
the on/off time of each channel is the same regardless of the delay. These delays prevent large inrush currents and switching noise that can
reduce bypass capacitance when the outputs are switched on.
OUT n Enable
All OUT n channels can be collectively switched off with one signal. When OEN is set to 1, all OUT n channels are disabled, regardless of the
device logic operations. The greyscale counter is also reset when OEN is set to 1.
When OEN is set to 0, all OUT n channels are in normal operation.
Table 9. Pin OEN Truth Table
OEN
0
1
OUT0:OUT15
Normal Operation
Disabled
Setting Maximum Channel Current
The maximum output current per channel is programmed by a single resistor, R IREF , which is placed between pin I REF and GND. The voltage
on pin I REF is set by an internal band gap V IREF (1.24V typ). The maximum channel current is equivalent to the current flowing through R IREF
multiplied by a factor of 31.5. The maximum output current is calculated as:
I MAX =
V IREF
x 31.5
(EQ 1)
R IREF
Where:
V IREF = 1.24V;
R IREF = User-selected external resistor.
Figure 7 on page 7 shows the maximum output current I OUT versus R IREF , where R IREF is the value of the resistor between I REF terminal to
GND, and I OUT is the constant output current of OUT0:OUT15.
Revision 1.13
10 - 19
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AS1115 DB-YELLOW
BOARD DEMO AS1115 YELLOW
AS1116 DB-YELLOW
BOARD DEMO AS1116 YELLOW
AS3691A EB
BOARD EVAL AS3691A
AS5030 DB
BOARD DEMO AS5030
AS5048-DB-1.0
BOARD DEMO AS5048
AS5215 DB
BOARD DEMO AS5215
AS5245 DB
BOARD DEMO AS5245
AS5304-DK-1.0
BOARD DEMO AS5304
相关代理商/技术参数
AS1112_1
制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:16-Channel LED Driver with Dot Correction and Greyscale PWM
AS1112_12
制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:16-Channel LED Dr iver wi th Dot Cor rect ion and Greyscale PWM
AS1112B
制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:16-Channel LED Driver with Dot Correction and Greyscale PWM
AS1112BBQFT
制造商:ams 功能描述:T&R / TQFN 5x5 32
AS1112B-BQFT
功能描述:IC DRIVER LED 16CHAN 32-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C
AS1112BQFT
制造商:AMS 功能描述:IC LED DRIVER CONSTANT CURRENT TQFN32 制造商:AMS 功能描述:IC, LED DRIVER, CONSTANT CURRENT, TQFN32; Topology:Constant Current; No. of Outputs:16; Output Current:80mA; Output Voltage:15V; Driver Case Style:TQFN; Input Voltage Min:3V; Input Voltage Max:5.5V; Dimming Control Type:PWM ;RoHS Compliant: Yes
AS1112-BQFT
功能描述:IC DRIVER LED 16-CHAN 32-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 特色产品:LM3445 TRIAC Dimmable LED Driver 标准包装:55 系列:PowerWise® 恒定电流:是 恒定电压:- 拓扑:PWM，降压（降压） 输出数:1 内部驱动器:无 类型 - 主要:- 类型 - 次要:高亮度 LED（HBLED） 频率:30kHz ~ 1MHz 电源电压:8 V ~ 12 V 输出电压:- 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:管件 工作温度:-40°C ~ 125°C 产品目录页面:1285 (CN2011-ZH PDF) 其它名称:LM3445M
AS1112C-BQFT
功能描述:IC DRIVER LED 16CHAN 32-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C